Iron on patch directions

Be very careful with polyester fabrics, since applying the high heat necessary for ironing on patches can burn the fabric or cause it to get discolored. Silk and other delicate fabrics are not good candidates for patches.

Items Needed. Prepare Clothing Iron. Patch Placement. Pressing Patch. Let it Cool. How To Patches. Customize Holidays. How to Decorate for the Holiday Season with Patches. Customize Gifts Holidays. Apply as much pressure as you can by pressing down firmly. Remove the iron and allow the patch to to cool. Lift the towel and check to see whether the patch is fixed on securely by gently rubbing at the edge with a finger, trying to lift it.

If it lifts up a bit, replace the towel and press it with the iron again for 10 seconds. If you're working with a paper transfer patch, wait until it is fully cool leave it for 10 minutes , then carefully peel off the paper.

Part 3. Consider sewing around the edges. For a completely secure patch, use a sewing machine or a needle and thread to secure the patch to the fabric. This greatly reduces the chances that the patch will fall off. Don't attempt to sew around the edge of printable paper patches. Don't wash the article more than necessary. Iron-on patches are meant to be permanent, but they do become loosened over time. Take care not to let the article get too dirty, since washing it may cause the patch to start coming off.

If you do need to wash the item, hand wash it using cold water. Allow it to air dry. While you can wash items that have iron-on patches properly attached, care must be taken. Only wash in cold to lukewarm water and where possible, hand wash the item. If washing in the machine, only use the gentle cycle.

Always turn the garment with the iron-on patch inside out when washing it. Try to keep washing to a minimum, to preserve the patch and if its edges fray a lot, you may need to trim them or even stitch them back down. Not Helpful 3 Helpful Patches can be added to luggage cases but whether or not it can be ironed in place depends on the material from which the luggage case is made.

Fabric luggage cases should be fine for ironing on patches. However, leather baggage cases will require the patches to be sewn or glued on, as heat should not be applied to leather. For synthetic cases rayon, nylon, etc. Always check the material on the case with its ironing suitability before deciding what to do. Not Helpful 4 Helpful 9.

Hold in place for about 30 to 60 seconds. It is a good idea to add an iron-on patch to a clean garment, as this removes the need to wash the iron-patch more than is necessary. Also, it's nicer to work with a clean garment and if you are concerned about potential shrinkage of the garment if new , the pre-wash will take care of that.

Finally, as odd as it may seem, it's also important to iron the section of the garment the patch will be applied to before adding the patch, to ensure there are no wrinkles caught up under the patch, creating unsightly bulges or making it difficult to iron on neatly. Not Helpful 3 Helpful 8. Double-sided fusible web which has the glue contained within the web or iron-on glue sheets are another suitable option, both activated by heat.

Such supplies should be available from your local craft store or online. Not Helpful 1 Helpful 2. When a patch falls off a garment, this usually indicates that either it has been subjected to too much heat in the dryer or too frequent washing. The adhesive is likely no longer sticky and you'll either need to add new adhesive or stitch the patch back on.

If you're not keen on sewing the patch back in place, the best option is to apply fusible webbing to the back of the patch cut to size , then iron the patch back on, following the manufacturer's instructions.

Not Helpful 0 Helpful 5. Removal of iron-on patches is possible through the application of heat or an adhesive remover. Not Helpful 1 Helpful 5. I'm trying to iron on a motorcycle patch to a leather vest and it's not working. This will be your pressing cloth and always be between the patch and the iron. Line up the patch where you want it, cover it with the pressing cloth, drop the iron on it, and press down hard for seconds. Don't move the iron back-and-forth like you are pressing a shirt, just press straight down and let the patch absorb all the heat.

You will be melting a thin layer of adhesive on the back of the patch into a hot tacky glue. Some thinner patches will take less time than thicker patches. Wrap your finger in a towel and as soon as the iron comes off, use your covered finger the patch will be scalding hot to press the patch into the item it is being ironed onto. Allow to fully cool before testing to see how well the patch stuck.

Posted on February 5, February 20, by a ffffvf. Instructions Before applying your patch wash and dry your garment first. Set the iron to a hot cotton setting. Place the patch in the desired location and cover with a thin piece of cloth. Iron and apply firm pressure evenly on the patch for approx sec. Iron the opposite side for approx sec to reinforce.